Can I Hang Baby Name in Nursery With Command Hooks

Download Article

Download Article

Wood letters are a fun, creative manner to spice up a room, allowing you to add names, words, or even full sentences to your wall. There are a number of different ways to hang the letters up, meaning you can cull the method nigh appropriate for your project, such every bit nails or ribbon for drywall or adhesive for brick.

1. 

   one

   Marker the spot where you lot desire to hang the letter. Hold your letter up against the wall and adjust it until you think information technology looks good. And so, using a pencil or the corner of a viscous note, marking the wall at the top center edge of the letter. If y'all're putting upwardly multiple letters, make marks for each before hanging anything upward to avert issues with spacing.^[1]

   • Lay the letters on the floor to check the spacing before you make marks on the walls.^[2]
   • Use a laser or bubble level at the base of where the messages will become to brand sure your letters are even.^[3]

2. 2

   Choose an agglutinative based on the size and weight of the letters. For heavier messages, grab double sided mounting record, large Velcro strips, or another thick, durable adhesive. For medium-weight letters, try Command strips or a like resealable fastener. For small messages, you may exist able to use pasty tack or a generic brand of tape.^[4]

   • Brand sure to choose an adhesive that won't damage wall paint.^[5]

   Advertisement

3. 

   3

   Prepare the adhesives. If yous're using tape, rip off multiple pieces and roll them into pocket-sized, hollow tubes with the gluey sides facing out. If you're using fasteners or like items, remove the small strips of paper covering the sticky sides of the adhesives. For tack, pull off multiple pieces and roll them into pocket-size balls.^[6]

4. 

   4

   Printing the adhesives to the back of your letter. Place the adhesives at multiple points on the back of the letter, spacing them out evenly so that each surface area has some support. If you're using tape, tack, or other pocket-sized adhesives, focus on joints and corners since they will help keep the letter flat against the wall. If y'all're using large fasteners or Velcro strips, place them on long stretches of wood and then they tin can support the bulkiest office of the letter.^[vii]

   • For Velcro and other adhesives that come up in 2 parts, press both parts together before sticking your letter of the alphabet to the wall.

5. 

   5

   Stick your letter of the alphabet to the wall. Agree your letter up so that the top center edge touches the mark you fabricated earlier. Then, printing it to the wall. Make sure to push downwards on every area containing an adhesive to ensure the letter is fully attached. If yous're using adhesives similar Command strips, concord them down for the corporeality of time listed on the packaging.

   Advertizement

1. i

   Marker the spot on your wall where you lot desire to hang the letter of the alphabet. Printing your letter to the wall and move it around until you're happy with the position. Then, marking the top center border of the letter with a pencil or the corner of a sticky annotation. To avoid spatial conflicts, make marks for every letter y'all intend to put up before hanging annihilation.^[8]

   • If yous're hanging several letters, place them on the floor and so you tin can visualize the space y'all desire between them.^[nine]

2. 

   ii

   Drill pocket-size holes in the back of your letter if necessary. Grab a power drill and, with the speed on depression, create small holes in the back of your letter. Use a drill head that can create holes larger than the smash you plan on hanging your letter of the alphabet from. The thicker the letter, the deeper the holes should be. If your letter came with pre-drilled holes, skip this step.^[x]

   • If your letter is symmetrical, drill ane or more holes nigh the top center of the object.
   • If your letter is not symmetrical, in addition to a pigsty near the peak center of the object, drill holes in any areas where the weight is strangely distributed, such as the bottom hook on a 'J.'

3. 

   3

   Make marks on your wall where the nails will go. Hold your letter up to the wall so that the pinnacle eye edge touches the marking you made before. Then, create small pencil marks on the wall that represent with the holes in the back of your letter of the alphabet. To make sure the marks are accurate, use a tape mensurate to find the altitude betwixt them and compare them to the distance between the holes in your letter.

   • As well, use a light amplification by stimulated emission of radiation level or ask someone to agree a chimera level where yous want the base of the messages to become. This will aid you make sure the messages are straight.^[11]

4. 

   4

   Hammer nails into the marked areas. Grab a nail with a caput that is slightly smaller than the holes in the back of your letter. Hold it up against one of your marks and, with a hammer, gently pound it into the wall. Leave enough of the nail exposed that you can easily hang your letter on it. Echo this for each mark.^[12]

   • For heavier letters, endeavor using wall anchors instead of nails.

5. 

   5

   Hang your letter on the nails. Identify the holes in the dorsum of your alphabetic character over the corresponding nails. So, remove your hands from the letter to make sure the nails can fully back up information technology. If the nails are positioned incorrectly, move them to a new spot. If they cannot hold the letter, endeavor replacing them with a sturdier object similar a wall anchor.

   Advertisement

1. 

   1

   Make marks on your wall where you want your letter and ribbon to sit. Printing your alphabetic character onto the wall at the spot you desire to hang it from. Adjust the letter until yous're happy with the placement, then mark the height middle edge of it with a gummy note or pencil. Using the aforementioned method, mark the position directly above your letter where y'all want the superlative of your ribbon to sit.^[13]

2. 

   2

   Observe the distance between the ii marks. Using a record measure, notice the altitude between the ribbon mark and the alphabetic character marker. The tape mensurate should go from merely beneath the letter marking to simply above the ribbon marking.^[xiv]

3. 

   iii

   Cut out a slice of ribbon but over twice as long as your measurement. With your tape measure out as a guide, stretch out a piece of ribbon that is twice every bit long as the altitude between the ii marks. Before cutting, pull out an extra one to two inches (two.v to 5.1 cm) to account for the fact that you'll be attaching the ribbon to the dorsum of the letter, not the top edge. So, cut the ribbon off the spool using scissors.^[15]

4. 

   four

   Set the ribbon to the dorsum of your letter using hot gum. With a glue gun, place two patches of hot glue on the back of your letter. Make sure the patches are spaced evenly apart. Then, press the ends of your ribbon onto the mucilage, creating a loop. Allow the glue dry out for one to 2 minutes.^[16]

5. 

   5

   Hammer a nail into the ribbon marker. Catch a smash stiff plenty to agree your letter of the alphabet; for most letters, a 4D or 6D nail will be more than than enough. Then, place it directly over the ribbon marking and gently hammer it into the wall. Go out a portion of the boom exposed so yous can hang your ribbon from information technology.^[17]

6. 

   6

   Hang your ribbon from the nail. Place the centre of your ribbon loop over the nail. Let information technology sit down for a few minutes to make certain both the hot glue and nail are sturdy enough to agree your letter. If the letter doesn't hang where you want it to, attempt adjusting the ribbon or moving the blast. If the smash can't support your letter, try replacing it with a strong spiral or wall anchor.

   Advertisement

Add New Question

• Question

  How do you know how to infinite out the letters?

  

  David Julien is a DIY Specialist and the Master Owner at Squeamish DIY based in Quebec, Canada. David specializes in creating plans to make unique, affordable, and modernistic home furnishings. He holds a BA in Graphic Design from the University of Quebec Outaouais. Nice DIY uses sustainable and loftier-quality materials to create products that are unproblematic to make for anybody.

  

  DIY Specialist

  Good Respond

• Question

  How do I brand sure the letters are level?

  

  David Julien is a DIY Specialist and the Primary Owner at Nice DIY based in Quebec, Canada. David specializes in creating plans to make unique, affordable, and mod home furnishings. He holds a BA in Graphic Design from the University of Quebec Outaouais. Nice DIY uses sustainable and high-quality materials to create products that are uncomplicated to brand for everyone.

  

  DIY Specialist

  Expert Respond

• Question

  What kind of adhesive should I use to hang letters?

  

  David Julien is a DIY Specialist and the Principal Owner at Overnice DIY based in Quebec, Canada. David specializes in creating plans to make unique, affordable, and modern home furnishings. He holds a BA in Graphic Design from the University of Quebec Outaouais. Nice DIY uses sustainable and loftier-quality materials to create products that are simple to make for everyone.

  

  DIY Specialist

  Expert Answer

Ask a Question

200 characters left

Include your electronic mail address to get a bulletin when this question is answered.

Submit

Advert

Things You'll Demand

• Wooden letter of the alphabet
• Pencil or sticky notes
• Tape measure
• Hammer
• Nails or wall anchors
• Ability drill (if necessary)

• Wooden letter
• Pencil or sticky notes
• Adhesives (record, Velcro strips, resealable fasteners, or mucilaginous tack)

• Wooden letter
• Ribbon
• Pencil or sticky notes
• Tape measure
• Scissors
• Hot gum gun
• Hammer
• Smash, wall anchor, or strong screw

• Before hanging the wooden letters, yous tin decorate them by painting or adding stickers.

Advertisement

• Be careful when working with tools similar hammers and power drills. For safety, wear heavy duty working gloves and goggles during use.

Advertizing

About This Article

Article Summary X

To mountain a wooden letter, first by placing the letter on your wall and, when it'southward positioned how you want it, mark the top edge with a pencil or sticky note. If your letter did non come with premade holes, drill some into the back of the forest. Then, press your letter against the top edge mark and create additional marks on the wall corresponding to each of the letter's holes. Hammer nails into the marked areas to create hooks, then hang your alphabetic character from them. To learn how to hang wooden letters using ribbon or adhesives, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 51,052 times.

Did this article help y'all?

canorearight.blogspot.com

Source: https://www.wikihow.com/Hang-Wooden-Letters-on-a-Wall

Share this post